ATEX/IECEx Certified Electric Trace Tubing

Dekoron Unitherm has taken a step beyond typical heat traced bundle suppliers by ensuring our bundles, not just the electric heat trace cable, meet the requirements set down in the ATEX and IECEx Standards for use in potentially explosive atmospheres.

Our systems approach to these products covers not only the electrical components, but also the tubing, thermal insulation, outer coverings and all other critical components; checking their ability to operate safely and efficiently in the environment where they will be used.

This allows the Engineer or Installer to easily and safely select and apply an electric heat trace bundle system that meets the needs of his specific application.

Datasheets Accessories Technical Bulletins

Bundles with Low Temperature SR Heaters
- Fibrous Glass Insulation - Imperial Tubing Sizes
- Fibrous Glass Insulation - Metric Tubing Sizes

Please register or log in

To have access to the complete information and specs about our products, please register a new account or make sure to log in.

Preview our Technical Bulletins

What tubing material must I use to meet ASTM standards
Stainless Steel Tubing - ASTM A269 or ASTM A213
Can I use thermistors to control temperature
What is the tolerance on Heated Hose length
Can I install Dekoron Unitherm bundles below grade
Common stainless steel grades used in Dekoron Unitherm bundles
What is Dual Certified Stainless Steel
Application and Installation of Dekron Line Sensing Thermostats
What type temperature controller is needed for a bundle with a CPD heater
What CPD heaters are used in Dekoron Unitherm bundles
Polymer Jackets on Dekoron Unitherm Products
Constant Power Density Heating Element
Fittings for Dekoron-Unitherm Bundles
Dekoron Unitherm Video Training Ch 1 - Sealing
Dekoron Unitherm Video Training Ch 2 - Electrical Power Connnection and Termination
Dekoron Unitherm Video Training Ch 3 - Bending Tube Bundles
Dekoron Unitherm Video Training Ch 4 - Routing and Supporting
Dekoron Unitherm Video Training Ch 5 - Testing and Commissioning

ATEX/IECEx Certified Electric Trace Tubing

Bundles with Low Temperature SR Heaters

Fibrous Glass Insulation - Imperial Tubing Sizes

Fibrous Glass Insulation - Metric Tubing Sizes

Ambient Sensing Thermostat

Line Sensing Thermostat

End Boot Kits

End Sealant

Cable Entry Seals

Please register or log in

To have access to the complete information and specs about our products, please register a new account or make sure to log in.

Preview our Technical Bulletins

What tubing material must I use to meet ASTM standards

Stainless Steel Tubing - ASTM A269 or ASTM A213

Can I use thermistors to control temperature

What is the tolerance on Heated Hose length

Can I install Dekoron Unitherm bundles below grade

Common stainless steel grades used in Dekoron Unitherm bundles

What is Dual Certified Stainless Steel

Application and Installation of Dekron Line Sensing Thermostats

What type temperature controller is needed for a bundle with a CPD heater

What CPD heaters are used in Dekoron Unitherm bundles

Polymer Jackets on Dekoron Unitherm Products

Constant Power Density Heating Element

Fittings for Dekoron-Unitherm Bundles

Dekoron Unitherm Video Training Ch 1 - Sealing

Dekoron Unitherm Video Training Ch 2 - Electrical Power Connnection and Termination

Dekoron Unitherm Video Training Ch 3 - Bending Tube Bundles

Dekoron Unitherm Video Training Ch 4 - Routing and Supporting

Dekoron Unitherm Video Training Ch 5 - Testing and Commissioning

Navigations

Quality Policy